Showing results 92 to 111 of 141
< previous
next >
Issue Date | Title | Author(s) |
2011 | Optimization of process parameter variability in 45 nm PMOS device using Taguchi method | Salehuddin, F. ; Ahmad, I. ; Hamid, F.A. ; Zaharim, A. |
2012 | Optimization of process parameter variation in 45nm p-channel MOSFET using L18 orthogonal array | Salehuddin, F. ; Ahmad, I. ; Hamid, F.A. ; Zaharim, A. ; Hamid, A.M.A. ; Menon, P.S. ; Elgomati, H.A. ; Majlis, B.Y. ; Apte, P.R. |
2013 | Optimization of process parameters for Si lateral PIN photodiode | Menon, P.S. ; Kalthom Tasirin, S. ; Ahmad, I. ; Fazlili Abdullah, S. |
2018 | Optimization of process parameters for threshold voltage and leakage current based on taguchi method | Noor Faizah, Z.A. ; Ahmad, I. ; Ker, P.J. ; Menon, P.S. ; Afifah Maheran, A.H. ; Mah, S.K. |
2009 | Optimization of PV-Wind-Hydro-Diesel hybrid system by minimizing excess capacity | Ab. Razak, J. ; Sopian, K. ; Ali, Y. ; Alghoul, M.A. ; Zaharim, A. ; Ahmad, I. |
2011 | Optimizing 35nm NMOS devices V TH and I LEAK by controlling active area and halo implantation dosage | Elgomati, H.A. ; Majlis, B.Y. ; Salehuddin, F. ; Ahmad, I. ; Zaharim, A. ; Hamid, F.A. |
2002 | Pass transistor logic ALU design | Wagiran, R. ; Chong, A.B. ; Ahmad, I. |
2007 | Pb-free BGA solder joint reliability improvement with Sn3.5Ag solder alloy on Ni/Au finish | Leng, E.P. ; Ding, M. ; Lindsay, W. ; Chopin, S. ; Ahmad, I. ; Jalar, A. |
2006 | Performances test statistics for single outlier detection in bilinear (1,1,1,1) models | Zaharim, A. ; Mohamed, I. ; Ahmad, I. ; Abdullah, S. ; Omar, M.Z. |
2016 | Process Parameters Optimization of 14nm MOSFET Using 2-D Analytical Modelling | Noor Faizah, Z.A. ; Ahmad, I. ; Ker, P.J. ; Siti Munirah, Y. ; Mohd Firdaus, R. ; Md Fazle, E. ; Menon, P.S. |
2006 | Pulse power failure model of power MOSFET due to electrical overstress using tasca method | Ismail, N.S. ; Ahmad, I. ; Husain, H. ; Chuah, S. |
2008 | Reduction of warpage occurrence on stack-die QFN using FEA and statistical method | Abdullah, I. ; Ahmad, I. ; Talib, M.Z.M. ; Kamarudin, M.N.B.C. |
2014 | Reflow soldering process for Sn3.5Ag solder on ENIG using rapid thermal processing system | Adhila Muhammad, N. ; Bais, B. ; Ahmad, I. |
2013 | Responsivity optimization of a MQW SOI-based lateral PIN photodiode using Taguchi's L27 orthogonal array | Menon, P.S. ; Tasirin, S.K. ; Ahmad, I. ; Abdullah, S.F. ; Apte, P.R. |
2000 | Review on policies, research & development in microelectronic industry in Malaysia | Ahmad, I.B. ; Sulaiman, N.B. |
2012 | Robust optimization of a silicon lateral pin photodiode | Kalthom Tasirin, S. ; Susthitha Menon, P. ; Ahmad, I. ; Fazlili Abdullah, S. |
2012 | Scaling down of the 32 nm to 22 nm gate length NMOS transistor | Afifah Maheran, A.H. ; Menon, P.S. ; Ahmad, I. ; Elgomati, H.A. ; Majlis, B.Y. ; Salehuddin, F. |
2008 | Selection of high strength encapsulant for MEMS devices undergoing high-pressure packaging | Hamzah, A.A. ; Husaini, Y. ; Majlis, B.Y. ; Ahmad, I. |
2009 | Simulation of fabrication process VDMOSFET transistor using Silvaco software | Abdullah, H. ; Jurait, J. ; Lennie, A. ; Nopiah, Z.M. ; Ahmad, I. |
2006 | Solder bump strength and failure mode of low-k flip chip device | Endut, Z. ; Ahmad, I. ; Swee, G.L.H. ; Sukemi, N.M. |