Showing results 110 to 129 of 141
< previous
next >
| Issue Date | Title | Author(s) |
| 2009 | Simulation of fabrication process VDMOSFET transistor using Silvaco software | Abdullah, H. ; Jurait, J. ; Lennie, A. ; Nopiah, Z.M. ; Ahmad, I. |
| 2006 | Solder bump strength and failure mode of low-k flip chip device | Endut, Z. ; Ahmad, I. ; Swee, G.L.H. ; Sukemi, N.M. |
| 2006 | Solder joint strength of lead free solders under multiple reflow and high temperature storage condition | Ahmad, I. ; Jalar, A. ; Majlis, B.Y. ; Leng, E.P. ; San, Y.S. |
| 2004 | Some aspects of surface morphology and elemental analysis study on non-wetting problem at die top | Salleh, M.M. ; Ahmad, I. ; Jalar, A. ; Omar, G. ; Abdullah, S.H. ; Arshad, M.K. |
| 2008 | Sputtered encapsulation as wafer level packaging for isolatable MEMS devices: A technique demonstrated on a capacitive accelerometer | Hamzah, A.A. ; Yunas, J. ; Majlis, B.Y. ; Ahmad, I. |
| 2009 | Statistical design of ultra-thin SiO2 for nanodevices | Hashim, U. ; Abdul Fatah, M.F.A. ; Ahmad, I. ; Majlis, B.Y. |
| 2012 | Statistical modeling of solar cell using Taguchi method and TCAD tool | Bahrudin, M.S. ; Abdullah, S.F. ; Ahmad, I. |
| 2016 | Statistical modelling of 14nm n-types MOSFET | Noor Faizah, Z.A. ; Ahmad, I. ; Ker, P.J. ; Siti Munirah, Y. ; Mohd Firdaus, R. ; Mah, S.K. ; Menon, P.S. |
| 2011 | Statistical optimization for process parameters to reduce variability of 32 nm PMOS transistor threshold voltage | Elgomati, H.A. ; Majlis, B.Y. ; Ahmad, I. ; Salehuddin, F. ; Hamid, F.A. ; Zaharim, A. ; Mohamad, T.Z. ; Apte, P.R. |
| 2014 | Statistical process modelling for 32nm high-K/metal gate PMOS device | Maheran, A.H.A. ; Noor Faizah, Z.A. ; Menon, P.S. ; Ahmad, I. ; Apte, P.R. ; Kalaivani, T. ; Salehuddin, F. |
| 2006 | Study of lifetime prediction of N-MOS transistor due to hot carrier effect | Ahmad, I. ; Kornain, Z. ; Idros, M.F.M. |
| 2014 | Study of the effect of WO3 and Bi2O3 on the microstructure and electrical properties of a TiO2 based varistor | Kothandapani, Z. ; Begum, S. ; Ahmad, I. ; Daud, I.R. ; Gholizadeh, S. |
| 2013 | Taguchi optimization of a SOI-based lateral PIN photodiode using SiGe/Si multilayer quantum well | Menon, P.S. ; Tasirin, S.K. ; Ahmad, I. ; Islam, S. ; Abdullah, S.F. |
| 2006 | TCAD simulation of local mechanical stress reduction by use of a compressive silicon nitride/silicon oxynitride etch stop bi-layer for CMOS performance enhancement | Ahmad, W.R.W. ; Kordesch, A.V. ; Ahmad, I. ; Chew, S.A. ; Yew, P.T.B. |
| 2006 | TCAD Simulation of STI stress effect on active length for 130nm technology | Ahmad, W.R.W. ; Kordesch, A.V. ; Ahmad, I. ; Yew, P.T.B. |
| 2012 | Technique to improve visibility for cycle time improvement in semiconductor manufacturing | Rahim, S.R.A. ; Ahmad, I. ; Chik, M.A. |
| 2004 | Temperature & zincation process effect on electrical resistivity of aluminum bond pad for under Bump Metallurgy (UBM) | Kornain, Z. ; Ahmad, I. ; Omar, G. |
| 2007 | The characterization of Al bond pad surface treatment in electroless nickel immersion gold (ENIG) deposition | Md Arshad, M.K. ; Jalar, A. ; Ahmad, I. ; Omar, G. |
| 2006 | The characterization of KrF photoresists and the effect of different chromophore bulkiness on line edge roughness (LER) for submicron technology | Yusri, A. ; Bakri, M. ; Manaf, M.J. ; Wahab, K.I.A. ; Ahmad, I.B. |
| 2008 | The effect of clean and no-clean flux in enhancing the wettability of eutectic solder bump flip chip PBGA | Amin, N. ; Cheah, A.Y. ; Kornain, Z. ; Ahmad, I. |
