Browsing by Title


Or, select a letter below to start browsing
0-9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Showing results 6097 to 6116 of 6557 < previous   next >
Issue DateTitleAuthor(s)
2015Taguchi modeling of process parameters in vdg-mosfet device for higher ION/IOFF ratioKaharudin, K.E. ; Salehuddin, F. ; Hamidon, A.H. ; Aziz, M.N.I.A. ; Ahmad, I. 
2014Taguchi optimization of a SiGe/Si quantum dot SOI-based lateral PIN photodiodeMenon, P.S. ; Tasirin, S.K. ; Ahmad, I. ; Abdullah, S.F. 
2013Taguchi optimization of a SOI-based lateral PIN photodiode using SiGe/Si multilayer quantum wellMenon, P.S. ; Tasirin, S.K. ; Ahmad, I. ; Islam, S. ; Abdullah, S.F. 
2013Tan delta measurement of paper insulated laminates using capacitance method from 300kHz to 50MHzGhani, A.B. ; Chakrabarty, C.K. ; Raymond, W.J.K. ; Hock, G.C. 
2017Tangent delta extraction of cable joints for aged 11kV underground cable systemPermal, N. ; Chakrabarty, C.K. ; Avinash, A.R. ; Marie, T. ; Shafi Abd Halim, H. 
2016Tangent delta low voltage high frequency ac method to measure HV underground XLPE cablesAvinash, A.R. ; Chakrabarty, C.K. ; Permal, N. ; Agileswari 
2013Task knowledge model for triage decision-supportHalim, S.A. ; Annamalai, M. ; Ahmad, R. ; Ahmad, M.S. 
2017Task transfer in software agent community with sincerity merit pointJaafar, N.H. ; Ahmad, M.S. ; Ahmad, A. 
2014Task-based modelling of the triage domain knowledgeAnnamalai, M. ; Halim, S.A. ; Ahmad, R. ; Ahmad, M.S. 
2006TCAD simulation of local mechanical stress reduction by use of a compressive silicon nitride/silicon oxynitride etch stop bi-layer for CMOS performance enhancementAhmad, W.R.W. ; Kordesch, A.V. ; Ahmad, I. ; Chew, S.A. ; Yew, P.T.B. 
2006TCAD Simulation of STI stress effect on active length for 130nm technologyAhmad, W.R.W. ; Kordesch, A.V. ; Ahmad, I. ; Yew, P.T.B. 
2011Technical feasibility studies for Langkawi WCO (waste cooking oil) derived-biodieselKumaran, P. ; Mazlini, N. ; Hussein, I. ; Nazrain, M. ; Khairul, M. 
2008Technical note: Life cycle cost analysis of design options selection for energy efficiency improvement of electric motorYanti, P.A.A. ; Mahlia, T.M.I. 
2012Technique to improve visibility for cycle time improvement in semiconductor manufacturingRahim, S.R.A. ; Ahmad, I. ; Chik, M.A. 
2011Techno-economic analysis and environmental impact of fuel economy labels for passenger cars in IndonesiaSilitonga, A.S. ; Atabani, A.E. ; Mahlia, T.M.I. ; Sebayang, A.H. 
2011Techno-economic analysis of a wind-solar hybrid renewable energy system with rainwater collection feature for urban high-rise applicationChong, W.T. ; Naghavi, M.S. ; Poh, S.C. ; Mahlia, T.M.I. ; Pan, K.C. 
2013Techno-economic analysis of an optimized photovoltaic and diesel generator hybrid power system for remote houses in a tropical climateIsmail, M.S. ; Moghavvemi, M. ; Mahlia, T.M.I. 
2016Techno-economic analysis of bioethanol production from rice straw by liquid-state fermentationHidayata, M.H.M. ; Salleh, S.F. ; Riayatsyahb, T.M.I. ; Aditiyac, H.B. ; Mahliaa, T.M.I. ; Shamsuddina, A.H. 
2012Techno-economic analysis of palm oil mill wastes to generate power for grid-connected utilizationMahlia, T.M.I. ; Yong, J.H. ; Safari, A. ; Mekhilef, S. 
2016Techno-economic and environmental assessment of bioethanol production from high starch and root yield Sri Kanji 1 cassava in MalaysiaHanif, M. ; Mahlia, T.M.I. ; Aditiya, H.B. ; Chong, W.T. ; Nasruddin